July 26, 2007 INSTALL 8 NetBSD

NAME

INSTALL - Installation procedure for NetBSD/sparc64.

CONTENTS

                                                              

About this Document............................................2 Quick install notes for the impatient..........................3 What is NetBSD?................................................3 Changes Between The NetBSD 3.0 and 4.0 Releases................4 Networking..................................................4 Filesystems.................................................4 Drivers.....................................................5 Platforms...................................................7 Kernel subsystems...........................................7 Security....................................................8 Userland....................................................8 Components removed from NetBSD.............................10 The Future of NetBSD..........................................10 Sources of NetBSD.............................................11 NetBSD 4.0_wrstuden_fixsa_t1 Release Contents.................11 NetBSD/sparc64 subdirectory structure......................12 Binary distribution sets...................................13 NetBSD/sparc64 System Requirements and Supported Devices......14 Supported machines.........................................14 Unsupported machines.......................................15 Supported devices..........................................15 Unsupported devices........................................16 Getting the NetBSD System on to Useful Media..................16 Preparing your System for NetBSD installation.................18 Deciding on partition sizes................................18 Setting up Open Firmware...................................19 Determining how to boot from an SBUS or PCI................19 Configuration of network interfaces........................21 Installing the NetBSD System..................................21 Installing NetBSD from CDROM...............................21 Installing NetBSD by using the NetBSD miniroot.............21 Installing NetBSD by using a NetBSD kernel on a............22 Installing NetBSD by using a netboot setup.................22 Running the sysinst installation program...................27 Introduction............................................27 General.................................................27 Quick install...........................................28 Booting NetBSD..........................................29 Network configuration...................................29 Installation drive selection and parameters.............29 Partitioning the disk...................................29 Preparing your hard disk................................30 Getting the distribution sets...........................30 Installation using ftp..................................30 Installation using NFS..................................31 Installation from CD-ROM................................31 Installation from an unmounted file system..............31 Installation from a local directory.....................31 Extracting the distribution sets........................31 Ensure you have the correct kernel installed............32 Finalizing your installation............................32 Manual Installation of NetBSD using Solaris................32 Preparing the disk in Solaris...........................33 Installing NetBSD Software from Solaris.................34 Creating NetBSD Device Nodes under Solaris..............34 Configuring the NetBSD system from Solaris..............34 Booting NetBSD for the first time.............................34 Post installation steps.......................................34 Upgrading a previously-installed NetBSD System................37 Compatibility Issues With Previous NetBSD Releases............38 Issues affecting an upgrade from NetBSD 2.1 and older......38 Issues affecting an upgrade from NetBSD 3.x releases.......38 Using online NetBSD documentation.............................39 Administrivia.................................................39 Thanks go to..................................................40 We are........................................................41 Legal Mumbo-Jumbo.............................................46 The End.......................................................52

DESCRIPTION

About this Document

This document describes the installation procedure for NetBSD 4.0_wrstuden_fixsa_t1 on the sparc64 platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt:

.ps
PostScript.

.html
Standard Internet HTML.

.more
The enhanced text format used on UNIX-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally presented.

.txt
Plain old ASCII.

You are reading the HTML version.

Quick install notes for the impatient

This section contains some brief notes describing what you need to install NetBSD 4.0_wrstuden_fixsa_t1 on a machine of the sparc64 architecture.

What is NetBSD?

The NetBSD Operating System is a fully functional Open Source UNIX-like operating system derived from the University of California, Berkeley Networking Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on fifty four different system architectures (ports), featuring seventeen machine architectures across fifteen distinct CPU families, and is being ported to more. The NetBSD 4.0_wrstuden_fixsa_t1 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distribution. For information on them, please see the NetBSD web site at http://www.NetBSD.org/.)

NetBSD is a completely integrated system. In addition to its highly portable, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code.

NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist.

Changes Between The NetBSD 3.0 and 4.0 Releases

The NetBSD4.0 release provides numerous significant functional enhancements, including support for many new devices, integration of hundreds of bug fixes, new and updated kernel subsystems, and many user-land enhancements. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems.

It is impossible to completely summarize more than a year of development that went into the NetBSD 4.0_wrstuden_fixsa_t1 release.

The complete list of changes can be found in the CHANGES: ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-4.0/CHANGES and CHANGES-4.0: ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-4.0/CHANGES-4.0 files in the top level directory of the NetBSD 4.0 release tree. Some highlights include:

Networking
Filesystems
Drivers
Platforms
Kernel subsystems

Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue.

Security
Userland

Besides this list, there there have also been innumerable bug fixes and other miscellaneous enhancements of course.

Components removed from NetBSD

In this release of NetBSD, some software components known from previous releases were removed from the system. In some cases those were components that are not useful anymore or their utility does not justify maintenance overhead. Other components were not working properly and there was lack of interest in fixing them.

The Future of NetBSD

The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of computer software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project.

The NetBSD Foundation will help improve the quality of NetBSD by:

We intend to begin narrowing the time delay between releases. Our ambition is to provide a full release every six to eight months.

We hope to support even more hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD.

We intend to continue our current practice of making the NetBSD-current development source available on a daily basis.

We intend to integrate free, positive changes from whatever sources submit them, providing that they are well thought-out and increase the usability of the system.

Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists.

Sources of NetBSD

Refer to http://www.NetBSD.org/mirrors/.

NetBSD 4.0_wrstuden_fixsa_t1 Release Contents

The root directory of the NetBSD 4.0_wrstuden_fixsa_t1 release is organized as follows:

.../NetBSD-4.0_wrstuden_fixsa_t1/

CHANGES
Changes since earlier NetBSD releases.

LAST_MINUTE
Last minute changes.

MIRRORS
A list of sites that mirror the NetBSD 4.0_wrstuden_fixsa_t1 distribution.

README.files
README describing the distribution's contents.

TODO
NetBSD's todo list (also somewhat incomplete and out of date).

patches/
Post-release source code patches.

source/
Source distribution sets; see below.

In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 4.0_wrstuden_fixsa_t1 has a binary distribution.

The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows:

gnusrc
This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets.
79 MB gzipped, 367 MB uncompressed

pkgsrc
This set contains the ``pkgsrc'' sources, which contain the infrastructure to build third-party packages.
24 MB gzipped, 200 MB uncompressed

sharesrc
This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more.
5 MB gzipped, 20 MB uncompressed

src
This set contains all of the base NetBSD 4.0_wrstuden_fixsa_t1 sources which are not in gnusrc, sharesrc, or syssrc.
37 MB gzipped, 176 MB uncompressed

syssrc
This set contains the sources to the NetBSD 4.0_wrstuden_fixsa_t1 kernel for all architectures; config(1); and dbsym(8).
26 MB gzipped, 140 MB uncompressed

xsrc
This set contains the sources to the X Window System.
84 MB gzipped, 450 MB uncompressed

All the above source sets are located in the source/sets subdirectory of the distribution tree.

The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command:
       # cd / ; tar -zxpf set_name.tgz

In each of the source distribution set directories, there are files which contain the checksums of the files in the directory:

BSDSUM
Historic BSD checksums for the various files in that directory, in the format produced by the command:
cksum -o 1 file.

CKSUM
POSIX checksums for the various files in that directory, in the format produced by the command:
cksum file.

MD5
MD5 digests for the various files in that directory, in the format produced by the command:
cksum-m file.

SYSVSUM
Historic AT&T System V UNIX checksums for the various files in that directory, in the format produced by the command:
cksum -o 2 file.

The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest possible range of system can check the integrity of the release files.

NetBSD/sparc64 subdirectory structure
The sparc64-specific portion of the NetBSD4.0_wrstuden_fixsa_t1 release is found in the sparc64 subdirectory of the distribution: .../NetBSD-4.0_wrstuden_fixsa_t1/sparc64/. It contains the following files and directories:

INSTALL.html
INSTALL.ps
INSTALL.txt
INSTALL.more
Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display.
binary/
kernel/
netbsd-GENERIC.gz
A gzipped NetBSD kernel containing code for everything supported in this release.
netbsd-INSTALL.gz
The install kernel.
sets/
sparc64 binary distribution sets; see below.
installation/
miniroot/
sparc64 miniroot file system image; see below.
misc/
Miscellaneous sparc64 installation utilities; see installation section, below.
netboot/
Netboot bootloader; see below.
Binary distribution sets
The NetBSD sparc64 binary distribution sets contain the binaries which comprise the NetBSD4.0_wrstuden_fixsa_t1 release for the sparc64. The binary distribution sets can be found in the sparc64/binary/sets subdirectory of the NetBSD4.0_wrstuden_fixsa_t1 distribution tree.

Note:
If you want to install 32-bit only binaries, you will still need to boot using the sparc64 installation tools. When it asks you for the distribution set to install, provide the NetBSD/sparc binary/sets. Be sure to use the 32 bit sparc kern-GENERIC_SUN4U.tgz kernel distribution. Otherwise, continue to follow the sparc64 installation procedure, not the sparc instructions.
Most people will want the 64-bit sparc64 distribution tree:

base
The NetBSD4.0_wrstuden_fixsa_t1 sparc64 base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally functional. It includes shared library support, and excludes everything described below.
18 MB gzipped, 56 MB uncompressed

comp
Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages.
22 MB gzipped, 88 MB uncompressed

etc
This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading.
1 MB gzipped, 1 MB uncompressed

games
This set includes the games and their manual pages.
4 MB gzipped, 8 MB uncompressed

kern-GENERIC
This set contains a NetBSD/sparc64 4.0_wrstuden_fixsa_t1 GENERIC kernel, named /netbsd. You must install this distribution set.
3 MB gzipped, 6 MB uncompressed

man
This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets.
8 MB gzipped, 30 MB uncompressed

misc
This set includes the (rather large) system dictionaries, the typesettable document set, and other files from /usr/share.
3 MB gzipped, 9 MB uncompressed

text
This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages.
2 MB gzipped, 8 MB uncompressed

NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 4.4.0. Binary sets for the X Window System are distributed with NetBSD. The sets are:

xbase
The basic files needed for a complete X client environment. This does not include the X servers.
7 MB gzipped, 20 MB uncompressed

xcomp
The extra libraries and include files needed to compile X source code.
12 MB gzipped, 50 MB uncompressed

xfont
Fonts needed by the X server and by X clients.
31 MB gzipped, 39 MB uncompressed

xetc
Configuration files for X which could be locally modified.
0.03 MB gzipped, 0.17 MB uncompressed

xserver
The X server. This includes Xsun, Xsun24, XsunMono and Xvfb servers with man pages.
6 MB gzipped, 14 MB uncompressed

The sparc64 binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz.

The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xpf command from the root directory ( / ) of your system. This utility is used only in a Traditional method installation.

Note:
Each directory in the sparc64 binary distribution also has its own checksum files, just as the source distribution does.

NetBSD/sparc64 System Requirements and Supported Devices

Supported machines
The minimal configuration requires 32 MB of RAM and ~60 MB of disk space. To install the entire system requires much more disk space, and to run X or compile the system, more RAM is recommended, as NetBSD with 32 MB of RAM feels like Solaris with 32 MB of RAM - slow. Note that until you have at least 64 MB of RAM, getting more RAM is more important than getting a faster CPU.

Not all of the machines listed here have been tested. Often Sun will use the same motherboard design in multiple models. For example, they'll release a Blade ("workstation") model, Enterprise or Fire ("server") model, and Netra or ft ("telco") model with essentially the same devices, as far as NetBSD is concerned. If one model in this scheme works, it is highly likely another will work.

Sun has also released a few models with names that might imply the systems are UltraSPARC-based but actually have an i386 class CPU. These systems might be supported by the i386 port of NetBSD. See the following site for more info on what system boards are in which models. http://sunsolve.sun.com/handbook_pub/Devices/System_Board/SYSBD_TOC.html (requires a SunSolve login with a valid Sun Service Plan)

Unsupported machines
Supported devices

There are a large number of untested PCI drivers that have never been tested on UltraSPARC PCI systems that may `just work'.

Unsupported devices

Getting the NetBSD System on to Useful Media

Note that if you are installing or upgrading from a writable media, the media can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted.

Installation is supported from several media types, including:

The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the various media are outlined below.

Note:
If you are installing the 32-bit sparc distribution sets, you will need to rename sparc/binary/sets/kern-GENERIC_SUN4U.tgz to kern-GENERIC.tgz since the sparc64 installation tools would otherwise attempt to install the kernel for 32-bit sparc computers which does not boot on sparc64 systems.

CD-ROM / DVD
Find out where the distribution set files are on the CD-ROM or DVD. Likely locations are binary/sets and sparc64/binary/sets.

Proceed to the instruction on installation.

MS-DOS floppy
NetBSD doesn't include split sets to keep the distribution size down. They can be created on a separate machine using the split(1) command, running e.g. split -b 235k base.tgz base. to split the base.tgz file from sparc64/binary/sets into files named base.aa, base.ab, and so on. Repeat this for all set_name.tgz files, splitting them into set_name.xx files. Count the number of set_name.xx files that make up the distribution sets you want to install or upgrade. You will need one sixth that number of 1.44 MB floppies.

Format all of the floppies with MS-DOS. Do not make any of them bootable MS-DOS floppies, i.e. don't use format /s to format them. (If the floppies are bootable, then the MS-DOS system files that make them bootable will take up some space, and you won't be able to fit the distribution set parts on the disks.) If you're using floppies that are formatted for MS-DOS by their manufacturers, they probably aren't bootable, and you can use them out of the box.

Place all of the set_name.xx files on the MS-DOS disks.

Once you have the files on MS-DOS disks, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading.

FTP
The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. If you don't have access to a functioning nameserver during installation, the IPv4 address of ftp.NetBSD.org is 204.152.184.36 and the IPv6 address is 2001:4f8:1:c:230:48ff:fe31:43f2 (as of December, 2006).

Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading.

Note:
This method of installation is recommended for those familiar with using BSD network configuration and management commands. If you aren't, this documentation should help, but is not intended to be all-encompassing.

NFS
Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the /etc/exports file on of the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privileges on the server.)

You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself.

Once the NFS server is set up properly and you have the information mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading.

Note:
This method of installation is recommended for those already familiar with using BSD network configuration and management commands. If you aren't, this documentation should help, but is not intended to be all-encompassing.

Tape
To install NetBSD from a tape, you need to make a tape that contains the distribution set files, in `tar' format.

If you're making the tape on a UNIX-like system, the easiest way to do so is probably something like:

       # tar -cf tape_device dist_directories

where tape_device is the name of the tape device that describes the tape drive you're using; possibly /dev/rst0, or something similar, but it will vary from system to system. (If you can't figure it out, ask your system administrator.) In the above example, dist_directories are the distribution sets' directories, for the distribution sets you wish to place on the tape. For instance, to put the misc, base, and etc distributions on tape (in order to do the absolute minimum installation to a new disk), you would do the following:


       # cd .../NetBSD-4.0_wrstuden_fixsa_t1
       # cd sparc64/binary
       # tar -cf tape_device misc etc kern

Note:
You still need to fill in tape_device in the example.

Once you have the files on the tape, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading.


Preparing your System for NetBSD installation

Deciding on partition sizes
If you're installing NetBSD/sparc64 for the first time it's a good idea to look at the partition sizes of the disk you plan to install NetBSD on. Will you be installing NetBSD onto the same disk as Solaris, on its own disk, or will you be netbooting? While NetBSD can work just fine on a disk shared with Solaris, the NetBSD installer does not currently support this. The limitation is that the NetBSD disklabel(8) writes partition info that Solaris is not familiar with. Therefore, if you are sharing a disk with Solaris, any time you change a partition table, you must do it from Solaris.

Assuming a classic partition scheme with / (root) and /usr file systems, a comfortable size for the NetBSD / partition is about 100 MB. A full binary installation including X11R6 takes nearly 350 MB in /usr. Since the pkgsrc binaries are typically installed in /usr/pkg you may want a significantly larger /usr partition. A good initial size for the swap partition is the amount of physical memory in your machine, if you've got more than 128 MB RAM. If you've got less RAM, you may want swap to be at least 128 MB.

Setting up Open Firmware
First, you need to stop your system from automatically booting when powered on. Pressing the STOP key (sometimes called the L1 key, found on the left side of your keyboard) and the a key will halt your system and give you the ``ok'' prompt. If you are using a serial console, send a ``BREAK'' signal from your terminal (the method of sending ``BREAK'' varies from terminal to terminal).

If the ethernet address of your sparc64 system is ff:ff:ff:ff:ff:ff (check with the Open Firmware ``banner'' command), then your NVRAM battery is dead and you will have trouble using ethernet (among other problems). Read the Sun NVRAM/Hostid FAQ. http://www.squirrel.com/squirrel/sun-nvram-hostid.faq.html

If you have a valid ethernet address and you plan to netboot, write down your system's ethernet address.

You cannot use the security modes of the SPARC OpenFirmware.

ok setenv security-mode none

If you are using a serial console, the NetBSD/sparc64 installer defaults to using 9600 bps, 8N1 settings. You may want to configure your system and serial terminal like this prior to booting the installer. Additionally, a new installation of NetBSD/sparc64 will default to these settings as well.

SCSI devices are specified by an Open Firmware devalias which provides simple mnemonics for the full path to the device. Type devalias to get a list of all of the available aliases. At a minimum, the alias and partition are necessary when booting.

Therefore, to boot from the swap partition on the internal hard drive one would use:

ok boot disk:b

To boot from a CD-ROM (Open Firmware assumes SCSI CD-ROMs are at target 6), one would use:

ok boot cdrom

And, to boot from a kernel named netbsd-GENERIC on the fourth partition ( `d', often the /usr partition) on an external SCSI hard drive (target 2, partition 3), one would use:

ok boot disk2:d netbsd-GENERIC

If you get ``.... Fast Data MMU Miss'' when booting after the NetBSD installation, your OpenBoot PROM may need updating. It has been reported that version 3.31 lead to a successful boot on an Ultra Enterprise 420R, while version 3.23 did not. Exact values may vary, depending on your hardware, current OpenBoot PROM version and moon phase.

Determining how to boot from an SBUS or PCI card
Some SBUS and PCI cards have firmware that lets you use them as a boot device. These cards do not automatically create a devalias entry, so you must traverse the device tree to figure out what Open Firmware calls your card. You will be using Open Firmware commands at the `ok' prompt. First `cd' to the top of the device tree and list the nodes there. The following is the procedure to boot from an IDE card in an UltraSPARC 30.
ok cd /
ok ls
f006cf08 SUNW,ffb@1e,0
f006c32c SUNW,UltraSPARC-II@0,0
f006002c counter-timer@1f,1c00
f005f410 pci@1f,2000
f005eb54 pci@1f,4000
f004cf84 virtual-memory
f004c9a4 memory@0,0
f002ce38 aliases
f002cdc8 options
f002cc90 openprom
f002cc24 chosen
f002cbb4 packages
Usually, you can simply type in the name before the at (@) sign and OpenFirmware will fill in the rest.
ok cd pci@1f,4000
ok ls
f0081524 ide@2
f007be50 scsi@3
f0074688 network@1,1
f0060324 ebus@1
ok cd ide@2
ok ls
0081fe4 cdrom
f0081938 disk
ok cd disk
ok ls
ok pwd
/pci@1f,4000/ide@2/disk
OK, now we know the path to the IDE device in this example. Now, we need to determine if it's capable of booting. If it is, it will have the word `open'.
ok words
close         load          write         read          seek
open          write-blocks  read-blocks   max-transfer
block-size    dma-free      dma-alloc     spin-down     spin-up
Great! Also, in case you're interested in further details about your hardware, you can use the `.properties' command.

So, when it's time to type in a boot command, use the shortened version of the pwd command. You need to be more specific if there are two devices with the same name (in this case, two /pci entries). In this example, you'd type:

ok boot /pci@1f,4000/ide/disk@0,0
You can also store this device path across reboots using the nvalias command.
ok nvalias wd0 /pci@1f,4000/ide/disk@0,0:a

And when the kernel is done booting, it may not automatically use your card as the root device -- you may need to type in the NetBSD/sparc64 name for that device:

root on sd0a dumps on sd0b
no file system for sd0 (dev 0x700)
cannot mount root, error = 79
root device (default sd0a): ?
use one of: hme0 sd0[a-h] wd0[a-h] halt
root device (default sd0a): wd0a
dump device: wd0a
file system (default generic): ffs
root on wd0a
Configuration of network interfaces
Some network devices (i.e. certain SBus cards) allow a choice between operating on a UTP or a AUI port. The le driver supports automatic detection of the port which is actually connected to the wire. If automatic detection is not available or not working properly in your environment, you may have to specify the type connection using the media parameter of ifconfig(8). During installation, you'll get the opportunity to specify the appropriate medium. Use 10base5/AUI to select the AUI connector, or 10baseT/UTP to select the UTP connector.

Installing the NetBSD System

Installing NetBSD is a relatively complex process, but if you have this document in hand it shouldn't be too much trouble.

There are several ways to install NetBSD onto a disk. The easiest way in terms of preliminary setup is to install from CDROM. If you don't have access to a CDROM or CDROM burner, you can use a miniroot image that can be booted off your local disk's swap partition. Alternatively, if your UltraSPARC is hooked up in a network you can find a server and arrange for a diskless setup which is a convenient way to install on a machine whose disk does not currently hold a usable operating system (see the section Installing NetBSD by using a diskless setup below).

If you have problems with these or you are installing NetBSD onto the same disk as Solaris, see the section below on Manual Installation of NetBSD using Solaris

Installing NetBSD from CDROM
Installing from CDROM, whether it has the full distribution or just a kernel and sysinst is the least painful way to install NetBSD. Simply insert the CD-ROM in the drive, power up the computer, and type:
ok boot cdrom

This Open Firmware boot command will cause the NetBSD kernel contained in the CD-ROM to be booted. After the initial probe messages you'll be asked to start the install or upgrade procedure. Proceed to the section Running the sysinst installation program below.

Installing NetBSD by using the NetBSD miniroot
The miniroot is a self-contained NetBSD file system holding all utilities necessary to install NetBSD on a local disk. It is distributed as a plain file designed to be transferred to a raw disk partition from which it can be booted using the appropriate OpenFirmware command. Usually, the miniroot will be loaded into the swap partition of a disk. If needed, you can use any other unused partition, but remember that the partition will then not available during the installation process.

Loading the miniroot onto your raw partition is simple using the dd(1) command. Just remember to first uncompress the miniroot image and boot your OS with the -s flag so that it runs ``single-user'' and does not attempt to start swapping.

ok boot -s

On Solaris you use a command like:

# gunzip miniroot.fs.gz
# dd if=miniroot.fs of=/dev/rdsk/c0t0d0s1 bs=4k
On NetBSD the command is:
# gunzip miniroot.fs.gz
# dd if=miniroot.fs of=/dev/rsd0b bs=4k
Replace /dev/rdsk/c0t0d0s1 or /dev/rsd0b with your swap partition.

After transferring the miniroot to disk, bring the system down by:

# halt
Then boot the miniroot by typing the appropriate command at the OpenFirmware prompt:
ok boot disk:b netbsd
If you've loaded the miniroot onto some other disk than sd0 use the correct devalias, such as
ok boot disk1:b netbsd
This Open Firmware boot command will cause the NetBSD kernel contained in the miniroot image to be booted. After the initial probe messages you'll be asked to start the install or upgrade procedure. Proceed to the section Running the sysinst installation program below.
Installing NetBSD by using a NetBSD kernel on a Solaris partition
This procedure is very straightforward. You will be putting the NetBSD installation kernel (kernel with a RAM disk installer) on your Solaris partition and telling Open Firmware to boot the NetBSD kernel.

CAVEAT: this method is a bit fragile. Depending on physical partition layout, partition size, and parameters used to create the filesystem of your Solaris root partition, bugs in the bootloader might be triggered and cause this method to fail.

First, copy the netbsd-INSTALL.gz kernel and bootloader to the root level of your hard drive and halt your system

# cp binary/kernel/netbsd-INSTALL.gz /
# cp installation/misc/ofwboot /
# halt
At the Open Firmware prompt, boot NetBSD.
ok boot disk:a /ofwboot -a
The -a flag is needed so that the bootloader will ask you to find your installation kernel.
Rebooting with command: boot disk:a /ofwboot -a
Boot device: /pci@1f,4000/scsi@3/disk@0,0:a  File and args: /ofwboot -a
Enter filename [/ofwboot]: <return>
>> NetBSD/sparc64 OpenFirmware Boot, Revision 1.7
>> (autobuild@tgm.netbsd.org, Thu May 20 16:29:20 UTC 2004)
Boot: netbsd-INSTALL.gz
After the initial probe messages you'll be asked to start the install or upgrade procedure. Proceed to the section Running the sysinst installation program below.
Installing NetBSD by using a netboot setup

  1. Introduction

    To netboot a sparc64, you must configure one or more servers to provide information and files to your sparc64 (the `client'). If you are using NetBSD (any architecture) on your netboot server(s), the information provided here should be sufficient to configure everything. Additionally, you may wish to look at the diskless(8) manual page and the manual pages for each daemon you'll be configuring. If the server(s) are another operating system, you should consult the NetBSD Diskless HOW-TO, which will walk you through the steps necessary to configure the netboot services on a variety of platforms. http://www.NetBSD.org/Documentation/network/netboot/

    You may either netboot the installer so you can install onto a locally attached disk, or you may run your system entirely over the network.

    Briefly, the netboot process involves discovery, bootstrap, kernel and file system stages. In the first stage, the client discovers information about where to find the bootstrap program. Next, it downloads and executes the bootstrap program. The bootstrap program goes through another discovery phase to determine where the kernel is located. The bootstrap program tries to mount the NFS share containing the kernel. Once the kernel is loaded, it starts executing. For RAM disk kernels, it mounts the RAM disk file system and begins executing the installer from the RAM disk. For normal (non-RAM disk) kernels, the kernel tries to mount the NFS share that had the kernel and starts executing the installation tools or init(8). All sparc64 systems use a combination of RARP and DHCP for the discovery stage. TFTP is used in the bootstrap phase to download the bootstrap program, ofwboot.net, which has been linked to a file name appropriate to the client's IP address as described in the TFTP section below. NFS is used in both the kernel and file system stages to download the kernel, and to access files on the file server.

    We will use `CC:CC:CC:CC:CC:CC' as the MAC address (ethernet hardware address) of your netboot client machine. You should have determined this address in an earlier stage. In this example, we will use `192.168.1.10' as the IP address of your client and `client.test.net' as its name. We will assume you're providing all of your netboot services on one machine called `server.test.net' with the client's files exported from the directory /export/client/root. You should, of course, replace all of these with the names, addresses, and paths appropriate to your environment.

    You should set up each netboot stage in order (i.e. discovery, bootstrap, kernel, and then file system) so that you can test them as you proceed.

  2. dhcpd(8) in bootpd(8) compatible mode

    Put the following lines in your /etc/dhcpd.conf (see dhcpd.conf(5) and dhcp-options(5) for more information):

    ddns-update-style none;
                    # Do not use any dynamic DNS features
                    #
    allow bootp;    # Allow bootp requests, thus the dhcp server
                    # will act as a bootp server.
                    #
    authoritative;  # master DHCP server for this subnet
                    #
    subnet 192.168.1.0 netmask 255.255.255.0 {
                    # Which network interface to listen on.
                    # The zeros indicate the range of addresses
                    # that are allowed to connect.
    }
    group {
                    # Set of parameters common to all clients
                    # in this "group".
                    #
            option broadcast-address        192.168.1.255;
            option domain-name              "test.net";
            option domain-name-servers      dns.test.net;
            option routers                  router.test.net;
            option subnet-mask              255.255.255.0;
                    #
                    # An individual client.
                    #
            host client.test.net {
                    hardware ethernet       CC:CC:CC:CC:CC:CC;
                    fixed-address           192.168.1.10;
                    #
                    # Name of the host (if the fixed address
                    # doesn't resolve to a simple name).
                    #
                    option host-name        "client";
                    #
                    # Name of the bootloader or kernel
                    # to download via tftp.
                                                                                         

    # # The path on the NFS server. # option root-path "/export/client/root";

    # # If your DHCP server is not your NFS server, supply the # address of the NFS server. Since we assume you run everything # on one server, this is not needed. # # next-server server.test.net; } #you may paste another "host" entry here for additional #clients on this network }

    You will need to make sure that the dhcpd.leases file exists.

    # touch /var/db/dhcpd.leases
    

    You will need to start the dhcpd. If it's already running, you will need to restart it to force it to re-read its configuration file. If the server is running NetBSD, you can achieve this with:

    # /etc/rc.d/dhcpd restart
    

  3. rarpd(8)

    Create an /etc/ethers file with the following line:

    CC:CC:CC:CC:CC:CC     client
    

    Add your client to the server's /etc/hosts file:

    192.168.1.10 client
    

    You will need to start the rarpd. If it's already running, you will need to restart it to force it to re-read its configuration file. If the server is running NetBSD, you can achieve this with:

    # /etc/rc.d/rarpd restart
    

  4. tftpd(8)

    The default configuration of the TFTP server is to run in a chroot(8) environment in the /tftpboot directory. Thus, the first order of business is to create this directory:

    # mkdir -p /tftpboot
    

    Next, edit /etc/inetd.conf and uncomment the line with the TFTP daemon:

    tftp  dgram  udp  wait  root  /usr/libexec/tftpd tftpd -l -s /tftpboot
    

    Now, restart inetd(8). If the server is running NetBSD, you can achieve this with:

    # /etc/rc.d/inetd restart
    

    Now, you need to copy the bootloader for your sparc64 machine to /tftpboot. Get ofwboot.net from the installation/netboot directory of the distribution.

    # cp ofwboot.net /tftpboot
    

    Now, you need to link ofwboot.net to the filename that your sparc64 will look for. It will look for a filename composed of the machine's IP address (in hexadecimal). For example, a machine which has been assigned IP address 192.168.1.10, will make a TFTP request for C0A8010A.

    You can use bc(1) to help calculate the filename:

    # bc
    obase=16
    192
    C0
    168
    A8
    1
    1
    10
    A
    quit
    # cd /tftpboot
    # ln -s ofwboot.net C0A8010A
    

    Just to be sure, let's make everything readable.

    # chmod -R a+rX /tftpboot
    

    Sometimes, the arp(8) table gets messed up, and the TFTP server can't communicate with the client. In this case, it will write a log message (via syslogd(8)) to /var/log/messages saying: `tftpd: write: Host is down'. If this is the case, you may need to force the server to map your client's ethernet address to its IP address:

    # arp -s client CC:CC:CC:CC:CC:CC
    

  5. nfsd(8), mountd(8), and rpcbind(8)

    Now your system should be able to load the bootstrap program and start looking for the kernel. Let's set up the NFS server. Create the directory you are exporting for the netboot client:

    # mkdir -p /export/client/root
    

    Put the following line in /etc/exports to enable NFS sharing:

    /export/client/root -maproot=root client.test.net
    

    If your server is currently running an NFS server, you only need to restart mountd(8). Otherwise, you need to start rpcbind(8) and nfsd(8). If the server is running NetBSD, you can achieve this with:

    # /etc/rc.d/rpcbind start
    # /etc/rc.d/nfsd start
    # /etc/rc.d/mountd restart
    

  6. NetBSD kernel and installation tools

    Now, if you place a kernel named netbsd in /export/client/root your client should boot the kernel. Use binary/kernel/netbsd-GENERIC.gz).

    # gunzip netbsd-GENERIC.gz
    # mv netbsd-GENERIC /export/client/root/netbsd
    

    If you are netbooting the installer, copy the distribution files to the client's root directory and extract the tools from installation/misc/instfs.tgz.

    # cp *tgz /export/client/root
    # cd /export/client/root
    # tar -xpzf instfs.tgz
    

  7. Client file system

    You can skip this step if you do not plan to run your client diskless after installation. Otherwise, you need to extract and set up the client's installation of NetBSD. The Diskless HOW-TO describes how to provide better security and save space on the NFS server over the procedure listed here. http://www.NetBSD.org/Documentation/network/netboot/nfs.html

  8. Setting up the server daemons

    If you want these services to start up every time you boot your server, make sure the following lines are present in your /etc/rc.conf:

    dhcpd=YES        dhcpd_flags="-q"
    rarpd=YES        rarpd_flags="-a"
    nfs_server=YES         # enable server daemons
    mountd=YES
    rpcbind=YES      rpcbind_flags="-l"   # -l logs libwrap
    

    Also, you'll need to make sure the tftpd line in /etc/inetd.conf remains uncommented.

Now, netboot your system from the server by entering the appropriate boot command at the Open Firmware prompt.

ok boot net netbsd
After the initial probe messages you'll be asked to start the install or upgrade procedure. Proceed to the section Running the sysinst installation program below.

Running the sysinst installation program

  1. Introduction

    Using sysinst, installing NetBSD is a relatively easy process. You still should read this document and have it in hand when doing the installation process. This document tries to be a good guideline for the installation and as such covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use.

  2. General

    The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installation system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst program from the command prompt. It is not necessary to reboot.

  3. Quick install

    First, let's describe a quick install. The other sections of this document go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instructions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example.

  4. Booting NetBSD

    You may want to read the boot messages, to notice your disk's name and capacity. Its name will be something like sd0 or wd0 and the geometry will be printed on a line that begins with its name. As mentioned above, you may need your disk's geometry when creating NetBSD's partitions. You will also need to know the name, to tell sysinst on which disk to install. The most important thing to know is that wd0 is NetBSD's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc.

    Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus.

  5. Network configuration

    If you will not use network operation during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu, and select the Configure network option. If you only want to temporarily use networking during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response in reply to answers relating to this.

  6. Installation drive selection and parameters

    To start the installation, select Install NetBSD to hard disk from the main menu.

    The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. Depending on how many disks are found, you may get a different message. You should see disk names like wd0, wd1, sd0 or sd1.

  7. Partitioning the disk

  8. Editing the NetBSD disklabel

    The partition table of the NetBSD part of a disk is called a disklabel. There are 4 layouts for the NetBSD part of the disk that you can pick from: Standard, Standard with X, Custom and Use Existing. The first two use a set of default values (that you can change) suitable for a normal installation, possibly including X. With the Custom option you can specify everything yourself. The last option uses the partition info already present on the disk.

    You will be presented with the current layout of the NetBSD disklabel, and given a chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap partition has a special type called swap. Some partitions in the disklabel have a fixed purpose.

    a
    Root partition (/)

    b
    Swap partition.

    c
    The NetBSD portion of the disk.

    d-h
    Available for other use. Traditionally, g is the partition mounted on /usr, but this is historical practice and not a fixed value.

    You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it something different, make sure the name is a single word and contains no special characters. You don't need to remember this name.

  9. Preparing your hard disk

    You are now at the point of no return. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to proceed, enter yes at the prompt.

    The install program will now label your disk and make the file systems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are running. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Otherwise, you can continue the installation program after pressing the return key.

  10. Getting the distribution sets

    The NetBSD distribution consists of a number of sets, that come in the form of gzipped tarfiles. A few sets must be installed for a working system, others are optional. At this point of the installation, you will be presented with a menu which enables you to choose from one of the following methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly.

    For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'.

  11. Installation using ftp

    To be able to install using ftp, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used.

    You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the ftp server.

    sysinst will proceed to transfer all the default set files from the remote site to your hard disk.

  12. Installation using NFS

    To be able to install using NFS, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used.

    You will also be asked to specify the host that you want to transfer the sets from, and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e. correctly exported to your machine.

    If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the NFS server.

  13. Installation from CD-ROM

    When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM player (usually cd0), and the directory name on the CD-ROM where the distribution files are.

    sysinst will then check if the files are indeed available in the specified location, and proceed to the actual extraction of the sets.

  14. Installation from an unmounted file system

    In order to install from a local file system, you will need to specify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location.

  15. Installation from a local directory

    This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file system that is already accessible. sysinst will ask you for the name of this directory.

  16. Extracting the distribution sets

    After the install sets containing the NetBSD distribution have been made available, you can either extract all the sets (a full installation), or only extract sets that you have selected. In the latter case, you will be shown the currently selected sets, and given the opportunity to select the sets you want. Some sets always need to be installed (kern, base) and etc they will not be shown in this selection menu.

    Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably, especially on machines with slow graphics consoles or serial consoles.

    After all the files have been extracted, all the necessary device node files will be created. If you have already configured networking, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the network configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can then set a password for the "root" account, to prevent the machine coming up without access restrictions.

  17. Ensure you have the correct kernel installed

    If you are installing from the 32-bit sparc distribution set, make sure that you installed the correct kernel. The sparc64 installation tools do not by default copy the correct 32-bit kernel. Unless you prepared ahead of time by renaming the kern-GENERIC_SUN4U.tgz to kern-GENERIC.tgz then you will need to follow the next few instructions.

    Go to the main installation menu, and select Utility menu and then select the Run /bin/sh option, which will give you a shell prompt. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard:
           # stty erase '^h'
           # stty erase '^?'

    Type the following command (replacing wd0a with the partition name of your destination root partition):
           # mount /dev/wd0a /mnt
           # cd /mnt
    Now you ned to mount the location of your distribution sets:
           # mount /dev/cd0a /mnt2
           # tar xpzvf /mnt2/sparc/binary/kernel/kern-GENERIC_SUN4U.tgz
           # umount /mnt
           # umount /mnt2
           # exit

  18. Finalizing your installation

    Congratulations, you have successfully installed NetBSD 4.0_wrstuden_fixsa_t1 . You can now reboot the machine, and boot NetBSD from hard disk.

Skip down to the section on Booting NetBSD for the first time

Manual Installation of NetBSD using Solaris
(Adapted from Murray Stokely's <murray@osd.bsdi.com> instructions)

You can use Solaris to prepare the NetBSD user-friendly installer or to perform a full manual installation of NetBSD. If you want to use the user-friendly miniroot installer or RAM disk installation kernel, follow the sections Installing NetBSD by using the NetBSD miniroot or Installing NetBSD by using a NetBSD kernel on a Solaris partition.

Manual installation from Solaris 10 is not possible because NetBSD cannot use the resulting UFS file system. It is possible to install Solaris 10 and NetBSD on the same disk. To do so, partition the disk with the Solaris format command, then boot NetBSD and perform a manual installation. Be careful not to write a NetBSD disklabel. Use the disklabel command to read the partition size, as constructed from the Solaris disklabel. By default the NetBSD newfs command writes a NetBSD disklabel. Avoid this by using the -F and -s arguments to newfs.

Booting NetBSD for the first time

Now it is time to boot NetBSD for the first time. You will boot from your disk using similar syntax as described above in Setting up Open Firmware and Determining how to boot from an SBUS or PCI card That is, boot from your first disk:

ok boot disk

Post installation steps

Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state, with the most important ones described below.

  1. Configuring /etc/rc.conf

    If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message

           /etc/rc.conf is not configured. Multiuser boot aborted.

    and with the root file system (/) mounted read-only. When the system asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with sun for a local console, or whatever is appropriate for your serial console (some systems display garbage with a sun terminal type, you may need to use sun-ss5) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard:
           # stty erase '^h'
           # stty erase '^?'
    At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with:
           # /sbin/mount -u -w /
    Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi-user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5).

    If your /usr directory is on a separate partition and you do not know how to use ed, you will have to mount your /usr partition to gain access to ex or vi. Do the following:


           # mount /usr
           # export TERM=sun

    If you have /var on a separate partition, you need to repeat that step for it. After that, you can edit /etc/rc.conf with vi(1). When you have finished, type exit at the prompt to leave the single-user shell and continue with the multi-user boot.

    Other values that need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute, furthermore add an ifconfig_int for your <int> network interface, along the lines of


           ifconfig_hme0="inet 123.45.67.89 netmask 255.255.255.0"

    or, if you have myname.my.dom in /etc/hosts:


           ifconfig_hme0="inet myname.my.dom netmask 255.255.255.0"

    To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventurous) run named(8). See resolv.conf(5) or named(8) for more information. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf.

    Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf.

  2. Select the proper terminal devices

    If you are using a serial console, you will have to edit the /etc/ttys file and change sun-ss5 to the appropriate terminal type, such as vt220.

  3. Logging in

    After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. If you're using the machine in a networked environment, you should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root.

    Unless you have connected an unusual terminal device as the console you can just press RETURN when it prompts for Terminal type? [...].

  4. Adding accounts

    Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database.

  5. The X Window System

    If you have installed the X Window System, look at the files in /usr/X11R6/lib/X11/doc for information.

    Don't forget to add /usr/X11R6/bin to your path in your shell's dot file so that you have access to the X binaries.

  6. Installing third party packages

    If you wish to install any of the software freely available for UNIX-like systems you are strongly advised to first check the NetBSD package system. This automatically handles any changes necessary to make the software run on NetBSD, retrieval and installation of any other packages on which the software may depend, and simplifies installation (and deinstallation), both from source and precompiled binaries.

  7. Misc

Upgrading a previously-installed NetBSD System

The upgrade to NetBSD4.0_wrstuden_fixsa_t1 is a binary upgrade; it can be quite difficult to update the system from an earlier version by recompiling from source, primarily due to interdependencies in the various components.

To do the upgrade, you must boot from the installer kernel using one of the methods described above. You must also have at least the base and kern binary distribution sets available, so that you can upgrade with them, using one of the upgrade methods described above. Finally, you must have sufficient disk space available to install the new binaries. Since files already installed on the system are overwritten in place, you only need additional free space for files which weren't previously installed or to account for growth of the sets between releases. If you have a few megabytes free on each of your root (/) and /usr partitions, you should have enough space.

Since upgrading involves replacing the kernel, the boot blocks on your NetBSD partition, and most of the system binaries, it has the potential to cause data loss. You are strongly advised to back up any important data on the NetBSD partition or on another operating system's partition on your disk before beginning the upgrade process.

The upgrade procedure using the sysinst tool is similar to an installation, but without the hard disk partitioning. sysinst will attempt to merge the settings stored in your /etc directory with the new version of NetBSD. Getting the binary sets is done in the same manner as the installation procedure; refer to the installation part of the document for how to do this. Also, some sanity checks are done, i.e. file systems are checked before unpacking the sets.

After a new kernel has been copied to your hard disk, your machine is a complete NetBSD4.0_wrstuden_fixsa_t1 system. However, that doesn't mean that you're finished with the upgrade process. You will probably want to update the set of device nodes you have in /dev. If you've changed the contents of /dev by hand, you will need to be careful about this, but if not, you can just cd into /dev, and run the command:

       # sh MAKEDEV all

Finally, you will want to delete old binaries that were part of the version of NetBSD that you upgraded from and have since been removed from the NetBSD distribution.


Compatibility Issues With Previous NetBSD Releases

Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 4.0_wrstuden_fixsa_t1 .

Issues affecting an upgrade from NetBSD 2.1 and older releases.
See the section below on upgrading from NetBSD 3.x as well.

It is very important that you populate the directory /etc/pam.d with appropriate configuration files for the Pluggable Authentication Modules (PAM) because you will not be able to login any more otherwise. Using postinstall as described below will take care of this. Please refer to http://www.netbsd.org/guide/en/chap-pam.html for documentation about PAM.

The following issues can generally be resolved by extracting the etc set into a temporary directory and running postinstall:

postinstall -s /path/to/etc.tgz check
postinstall -s /path/to/etc.tgz fix

Issues fixed by postinstall:

The following issues need to be resolved manually:

Issues affecting an upgrade from NetBSD 3.x releases.

The following issues can generally be resolved by extracting the etc set into a temporary directory and running postinstall:

postinstall -s /path/to/etc.tgz check
postinstall -s /path/to/etc.tgz fix

Issues fixed by postinstall:

The following issues need to be resolved manually:

Using online NetBSD documentation

Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are

The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8.

The man command is used to view the documentation on a topic, and is started by entering man[ section] topic. The brackets [] around the section should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after logging in, enter


       # man passwd

to read the documentation for passwd(1). To view the documentation for passwd(5), enter


       # man 5 passwd

instead.

If you are unsure of what man page you are looking for, enter


       # apropos subject-word

where subject-word is your topic of interest; a list of possibly related man pages will be displayed.

Administrivia

If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instructions.

There are various mailing lists set up to deal with comments and questions about this release. Please send comments to: netbsd-comments@NetBSD.org.

To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: netbsd-bugs@NetBSD.org.

Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks.

There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/MailingLists/. If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below).

If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-help@NetBSD.org.

As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it.

Thanks go to

We are...

(in alphabetical order)


The NetBSD core group:
Alistair Crooksagc@NetBSD.org
YAMAMOTO Takashiyamt@NetBSD.org
Matt Thomasmatt@NetBSD.org
Valeriy E. Ushakovuwe@NetBSD.org
Christos Zoulaschristos@NetBSD.org

The portmasters (and their ports):
Anders Magnussonragge vax
Andrey Petrovpetrov sparc64
Ben Harrisbjh21 acorn26
Cherry G. Mathewcherry ia64
Chris Gilbertchris cats
Darrin Jewelldbj next68k
Erik Berlscyber cobalt
Frank van der Lindenfvdl amd64
Frank van der Lindenfvdl i386
Gavan Fantomgavan iyonix
IWAMOTO Toshihirotoshii hpcarm
Ichiro FUKUHARAichiro hpcarm
Ignatios Souvatzisis amiga
Izumi Tsutsuitsutsui ews4800mips
Izumi Tsutsuitsutsui hp300
Izumi Tsutsuitsutsui news68k
Jaime A Fournierober zaurus
Jason Thorpethorpej algor
Jason Thorpethorpej evbarm
Jason Thorpethorpej shark
Jonathan Stonejonathan pmax
Julian Colemanjdc atari
Manuel Bouyerbouyer xen
Marcus Comstedtmarcus dreamcast
Martin Husemannmartin sparc64
Matt Fredettefredette sun2
Matt Thomasmatt alpha
Matt Thomasmatt netwinder
Matthias Drochnerdrochner cesfic
Michael Lorenzmacallan macppc
NISHIMURA Takeshinsmrtks x68k
Nathan Williamsnathanw sun3
Nick Hudsonskrll hp700
Noriyuki Sodasoda arc
Paul Kranenburgpk sparc
Phil Nelsonphil pc532
Reinoud Zandijkreinoud acorn32
Ross Harveyross alpha
Søren Jørvangsoren sgimips
Scott Reynoldsscottr mac68k
Shin Takemuratakemura hpcmips
Simon Burgesimonb evbmips
Simon Burgesimonb pmax
Simon Burgesimonb sbmips
Steve Woodfordscw evbppc
Steve Woodfordscw mvme68k
Steve Woodfordscw mvmeppc
Takayoshi Kochikochi ia64
Tim Rightnourgarbled prep
Tohru Nishimuranisimura luna68k
Tohru Nishimuranisimura sandpoint
UCHIYAMA Yasushiuch hpcsh
UCHIYAMA Yasushiuch playstation2
Wayne Knowleswdk mipsco
Wolfgang Solfrankws ofppc

The NetBSD 4.0_wrstuden_fixsa_t1 Release Engineering team:
Grant Beattiegrant@NetBSD.org
Manuel Bouyerbouyer@NetBSD.org
David Brownleeabs@NetBSD.org
Pavel Cahynapavel@NetBSD.org
James Chaconjmc@NetBSD.org
Julian Colemanjdc@NetBSD.org
Håvard Eidneshe@NetBSD.org
Liam J. Foyliamjfoy@NetBSD.org
John Heasleyheas@NetBSD.org
Geert Hendrickxghen@NetBSD.org
Soren Jacobsensnj@NetBSD.org
Daniel de Kokdaniel@NetBSD.org
Phil Nelsonphil@NetBSD.org
Jeff Rizzoriz@NetBSD.org

NetBSD Developers:
Nathan Ahlstromnra@NetBSD.org
Steve Allenwormey@NetBSD.org
Jukka Andbergjandberg@NetBSD.org
Julian Assangeproff@NetBSD.org
Lennart Augustssonaugustss@NetBSD.org
Christoph Badurabad@NetBSD.org
Bang Jun-Youngjunyoung@NetBSD.org
Dieter Barondillo@NetBSD.org
Robert V. Baronrvb@NetBSD.org
Alan Barrettapb@NetBSD.org
Grant Beattiegrant@NetBSD.org
Jason Beeganjtb@NetBSD.org
Erik Berlscyber@NetBSD.org
Hiroyuki Besshobsh@NetBSD.org
John Birrelljb@NetBSD.org
Mason Loring Blissmason@NetBSD.org
Charles Blundellcb@NetBSD.org
Rafal Bonirafal@NetBSD.org
Stephen Borrillsborrill@NetBSD.org
Sean Boudreauseanb@NetBSD.org
Manuel Bouyerbouyer@NetBSD.org
John Brezakbrezak@NetBSD.org
Allen Briggsbriggs@NetBSD.org
Mark Brinicombemark@NetBSD.org
Aaron Brownabrown@NetBSD.org
Andrew Brownatatat@NetBSD.org
David Brownleeabs@NetBSD.org
Frederick Bruckmanfredb@NetBSD.org
Jon Bullerjonb@NetBSD.org
Simon Burgesimonb@NetBSD.org
Robert Byrnesbyrnes@NetBSD.org
Pavel Cahynapavel@NetBSD.org
D'Arcy J.M. Caindarcy@NetBSD.org
Dave Carrelcarrel@NetBSD.org
Daniel Carosonedan@NetBSD.org
James Chaconjmc@NetBSD.org
Bill Coldwellbillc@NetBSD.org
Julian Colemanjdc@NetBSD.org
Ben Collverben@NetBSD.org
Jeremy Cooperjeremy@NetBSD.org
Chuck Cranorchuck@NetBSD.org
Alistair Crooksagc@NetBSD.org
Aidan Cullyaidan@NetBSD.org
Garrett D'Amoregdamore@NetBSD.org
Johan Danielssonjoda@NetBSD.org
John Darrowjdarrow@NetBSD.org
Jed Davisjld@NetBSD.org
Matt DeBergalisdeberg@NetBSD.org
Arnaud Degrootedegroote@NetBSD.org
Rob Dekerdeker@NetBSD.org
Chris G. Demetrioucgd@NetBSD.org
Tracy Di Marco Whitegendalia@NetBSD.org
Jaromír Dolecekjdolecek@NetBSD.org
Andy Doranad@NetBSD.org
Roland Dowdeswellelric@NetBSD.org
Emmanuel Dreyfusmanu@NetBSD.org
Matthias Drochnerdrochner@NetBSD.org
Jun Ebiharajun@NetBSD.org
Håvard Eidneshe@NetBSD.org
Stoned Elipotseb@NetBSD.org
Michael van Elstmlelstv@NetBSD.org
Enami Tsugutomoenami@NetBSD.org
Bernd Ernestiveego@NetBSD.org
Erik Fairfair@NetBSD.org
Gavan Fantomgavan@NetBSD.org
Hauke Fathhauke@NetBSD.org
Hubert Feyrerhubertf@NetBSD.org
Jason R. Finkjrf@NetBSD.org
Matt J. Flemingmjf@NetBSD.org
Liam J. Foyliamjfoy@NetBSD.org
Matt Fredettefredette@NetBSD.org
Thorsten Frueauffrueauf@NetBSD.org
Castor Fucastor@NetBSD.org
Ichiro Fukuharaichiro@NetBSD.org
Quentin Garniercube@NetBSD.org
Thomas Gernerthomas@NetBSD.org
Simon J. Gerratysjg@NetBSD.org
Justin Gibbsgibbs@NetBSD.org
Chris Gilbertchris@NetBSD.org
Eric Gillespieepg@NetBSD.org
Adam Glassglass@NetBSD.org
Michael Graffexplorer@NetBSD.org
Brian C. Graysonbgrayson@NetBSD.org
Matthew Greenmrg@NetBSD.org
Andreas Gustafssongson@NetBSD.org
Jun-ichiro itojun Haginoitojun@NetBSD.org
Juergen Hannken-Illjeshannken@NetBSD.org
Charles M. Hannummycroft@NetBSD.org
Ben Harrisbjh21@NetBSD.org
Ross Harveyross@NetBSD.org
Eric Haszlakiewiczerh@NetBSD.org
John Hawkinsonjhawk@NetBSD.org
HAMAJIMA Katsuomihamajima@NetBSD.org
HAYAKAWA Koichihaya@NetBSD.org
John Heasleyheas@NetBSD.org
Geert Hendrickxghen@NetBSD.org
René Hexelrh@NetBSD.org
Iain Hibbertplunky@NetBSD.org
Kouichirou Hiratsukahira@NetBSD.org
Michael L. Hitchmhitch@NetBSD.org
Jachym Holecekfreza@NetBSD.org
Christian E. Hoppschopps@NetBSD.org
Ken Hornsteinkenh@NetBSD.org
Marc Horowitzmarc@NetBSD.org
Eduardo Horvatheeh@NetBSD.org
Nick Hudsonskrll@NetBSD.org
Shell Hungshell@NetBSD.org
Martin Husemannmartin@NetBSD.org
Dean Huxleydean@NetBSD.org
Love Hörnquist Åstrandlha@NetBSD.org
Bernardo Innocentibernie@NetBSD.org
Tetsuya Isakiisaki@NetBSD.org
ITOH Yasufumiitohy@NetBSD.org
IWAMOTO Toshihirotoshii@NetBSD.org
Matthew Jacobmjacob@NetBSD.org
Soren Jacobsensnj@NetBSD.org
Lonhyn T. Jasinskyjlonhyn@NetBSD.org
Darrin Jewelldbj@NetBSD.org
Nicolas Jolynjoly@NetBSD.org
Chris Jonescjones@NetBSD.org
Søren Jørvangsoren@NetBSD.org
Takahiro Kambetaca@NetBSD.org
Antti Kanteepooka@NetBSD.org
Masanori Kanaokakanaoka@NetBSD.org
Frank Kardelkardel@NetBSD.org
Mattias Karlssonkeihan@NetBSD.org
KAWAMOTO Yosihisakawamoto@NetBSD.org
Mario Kempermagick@NetBSD.org
Min Sik Kimminskim@NetBSD.org
Thomas Klausnerwiz@NetBSD.org
Klaus Kleinkleink@NetBSD.org
John Klosjklos@NetBSD.org
Wayne Knowleswdk@NetBSD.org
Takayoshi Kochikochi@NetBSD.org
John Kohljtk@NetBSD.org
Daniel de Kokdaniel@NetBSD.org
Paul Kranenburgpk@NetBSD.org
Lubomir Kundraklkundrak@NetBSD.org
Martti Kuparinenmartti@NetBSD.org
Kentaro A. Kurahonekurahone@NetBSD.org
Kevin Laheykml@NetBSD.org
David Laightdsl@NetBSD.org
Johnny C. Lamjlam@NetBSD.org
Martin J. Laubachmjl@NetBSD.org
Greg Leheygrog@NetBSD.org
Ted Lemonmellon@NetBSD.org
Christian Limpachcl@NetBSD.org
Frank van der Lindenfvdl@NetBSD.org
Joel Lindholmjoel@NetBSD.org
Mike Longmikel@NetBSD.org
Michael Lorenzmacallan@NetBSD.org
Warner Loshimp@NetBSD.org
Tomasz Luchowskizuntum@NetBSD.org
Federico Lupifederico@NetBSD.org
Brett Lymnblymn@NetBSD.org
Paul Mackerraspaulus@NetBSD.org
Anders Magnussonragge@NetBSD.org
MAEKAWA Masahidegehenna@NetBSD.org
David Maxwelldavid@NetBSD.org
Dan McMahilldmcmahill@NetBSD.org
Gregory McGarrygmcgarry@NetBSD.org
Jared D. McNeilljmcneill@NetBSD.org
Neil J. McRaeneil@NetBSD.org
Perry Metzgerperry@NetBSD.org
Simas Mockeviciussymka@NetBSD.org
Juan Romero Pardinesxtraeme@NetBSD.org
Julio M. Merino Vidaljmmv@NetBSD.org
Minoura Makotominoura@NetBSD.org
Luke Mewburnlukem@NetBSD.org
der Mousemouse@NetBSD.org
Joseph Myersjsm@NetBSD.org
Ken Nakatakenn@NetBSD.org
Takeshi Nakayamanakayama@NetBSD.org
Phil Nelsonphil@NetBSD.org
John Nemethjnemeth@NetBSD.org
Bob Nestorrnestor@NetBSD.org
NISHIMURA Takeshinsmrtks@NetBSD.org
Tohru Nishimuranisimura@NetBSD.org
NONAKA Kimihirononaka@NetBSD.org
Takehiko NOZAKItnozaki@NetBSD.org
Tobias Nygrentnn@NetBSD.org
OBATA Akioobache@NetBSD.org
Jesse Offjoff@NetBSD.org
Tatoku Ogaitotacha@NetBSD.org
OKANO Takayoshikano@NetBSD.org
Masaru Okioki@NetBSD.org
Atsushi Onoeonoe@NetBSD.org
Greg Osteroster@NetBSD.org
Jonathan Perkinsketch@NetBSD.org
Herb Peyerlhpeyerl@NetBSD.org
Matthias Pfallermatthias@NetBSD.org
Chris Pinnockcjep@NetBSD.org
Adrian Portelliadrianp@NetBSD.org
Rui Paulorpaulo@NetBSD.org
Peter Postmapeter@NetBSD.org
Dante Profetadante@NetBSD.org
Chris Provenzanoproven@NetBSD.org
Niels Provosprovos@NetBSD.org
Mindaugas Rasiukeviciusrmind@NetBSD.org
Michael Rauchmrauch@NetBSD.org
Marc Rechtrecht@NetBSD.org
Darren Reeddarrenr@NetBSD.org
Jeremy C. Reedreed@NetBSD.org
Antoine Reillestonio@NetBSD.org
Tyler R. Retzlaffrtr@NetBSD.org
Scott Reynoldsscottr@NetBSD.org
Michael Richardsonmcr@NetBSD.org
Tim Rightnourgarbled@NetBSD.org
Alan Ritterrittera@NetBSD.org
Jeff Rizzoriz@NetBSD.org
Gordon Rossgwr@NetBSD.org
Steve Rumblerumble@NetBSD.org
Ilpo Ruotsalainenlonewolf@NetBSD.org
Heiko W. Rupphwr@NetBSD.org
David Saintydsainty@NetBSD.org
SAITOH Masanobumsaitoh@NetBSD.org
Kazuki Sakamotosakamoto@NetBSD.org
Curt Sampsoncjs@NetBSD.org
Wilfredo Sanchezwsanchez@NetBSD.org
Ty Sarnatsarna@NetBSD.org
SATO Kazumisato@NetBSD.org
Jan Schaumannjschauma@NetBSD.org
Matthias Schelertron@NetBSD.org
Karl Schilke (rAT)rat@NetBSD.org
Amitai Schlairschmonz@NetBSD.org
Konrad Schroderperseant@NetBSD.org
Georg Schwarzschwarz@NetBSD.org
Lubomir Sedlaciksalo@NetBSD.org
Christopher SEKIYAsekiya@NetBSD.org
Reed Shadgettdent@NetBSD.org
John Shannonshannonjr@NetBSD.org
Tim Shepardshep@NetBSD.org
Takeshi Shibagakishiba@NetBSD.org
Naoto Shimazakiigy@NetBSD.org
Takao Shinoharashin@NetBSD.org
Takuya SHIOZAKItshiozak@NetBSD.org
Daniel Siegerdsieger@NetBSD.org
Chuck Silverschs@NetBSD.org
Thor Lancelot Simontls@NetBSD.org
Jeff Smithjeffs@NetBSD.org
Noriyuki Sodasoda@NetBSD.org
Wolfgang Solfrankws@NetBSD.org
T K Spindlerdogcow@NetBSD.org
SOMEYA Yoshihikosomeya@NetBSD.org
Bill Sommerfeldsommerfeld@NetBSD.org
Jörg Sonnenbergerjoerg@NetBSD.org
Ignatios Souvatzisis@NetBSD.org
Bill Squiergroo@NetBSD.org
Jonathan Stonejonathan@NetBSD.org
Bill Studenmundwrstuden@NetBSD.org
Kevin Sullivansullivan@NetBSD.org
SUNAGAWA Keikikei@NetBSD.org
Kimmo Suominenkim@NetBSD.org
Shin Takemuratakemura@NetBSD.org
TAMURA Kentkent@NetBSD.org
Shin'ichiro TAYAtaya@NetBSD.org
Ian Lance Taylorian@NetBSD.org
Matt Thomasmatt@NetBSD.org
Jason Thorpethorpej@NetBSD.org
Christoph Toshoktoshok@NetBSD.org
Greg Troxelgdt@NetBSD.org
Tsubai Masanaritsubai@NetBSD.org
Izumi Tsutsuitsutsui@NetBSD.org
UCHIYAMA Yasushiuch@NetBSD.org
Masao Uebayashiuebayasi@NetBSD.org
Shuichiro URATAur@NetBSD.org
Valeriy E. Ushakovuwe@NetBSD.org
Todd Vierlingtv@NetBSD.org
Aymeric Vincentaymeric@NetBSD.org
Paul Vixievixie@NetBSD.org
Mike M. Volokhovmishka@NetBSD.org
Krister Walfridssonkristerw@NetBSD.org
Lex Wennmacherwennmach@NetBSD.org
Leo Weppelmanleo@NetBSD.org
Assar Westerlundassar@NetBSD.org
Todd Whiteseltoddpw@NetBSD.org
Nathan Williamsnathanw@NetBSD.org
Rob Windsorwindsor@NetBSD.org
Dan Winshipdanw@NetBSD.org
Arnaud Lacombealc@NetBSD.org
Jim Wisejwise@NetBSD.org
Michael Wolfsonmbw@NetBSD.org
Steve Woodfordscw@NetBSD.org
Colin Woodender@NetBSD.org
YAMAMOTO Takashiyamt@NetBSD.org
Yuji Yamanoyyamano@NetBSD.org
Reinoud Zandijkreinoud@NetBSD.org
S.P.Zeidlerspz@NetBSD.org
Maria Zevenhovenmaria7@NetBSD.org
Christos Zoulaschristos@NetBSD.org

Other contributors:
Dave Burgessburgess@cynjut.infonet.net
Brian R. Gaekebrg@dgate.org
Brad Granthamgrantham@tenon.com
Lawrence Kestelootkesteloo@cs.unc.edu
Waldi Ravenswaldi@moacs.indiv.nl.net

Legal Mumbo-Jumbo

All product names mentioned herein are trademarks or registered trademarks of their respective owners.

The following notices are required to satisfy the license terms of the software that we have mentioned in this document:

NetBSD is a registered trademark of The NetBSD Foundation, Inc.

This product includes software developed by the University of California, Berkeley and its contributors.
This product includes software developed by the NetBSD Foundation.
This product includes software developed by The NetBSD Foundation, Inc. and its contributors.
This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD.
This product contains software developed by Ignatios Souvatzis for the NetBSD project.
This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project.
This product contains software written by Michael L. Hitch for the NetBSD project.
This product includes cryptographic software written by Eric Young (eay@cryptsoft.com)
This product includes cryptographic software written by Eric Young (eay@mincom.oz.au)
This product includes software designed by William Allen Simpson.
This product includes software developed at Ludd, University of Lulea, Sweden and its contributors.
This product includes software developed at Ludd, University of Lulea.
This product includes software developed at the Information Technology Division, US Naval Research Laboratory.
This product includes software developed by Berkeley Software Design, Inc.
This product includes software developed by David Jones and Gordon Ross
This product includes software developed by Gordon W. Ross and Leo Weppelman.
This product includes software developed by Hellmuth Michaelis and Joerg Wunsch
This product includes software developed by Internet Research Institute, Inc.
This product includes software developed by Leo Weppelman and Waldi Ravens.
This product includes software developed by Mika Kortelainen
This product includes software developed by Aaron Brown and Harvard University.
This product includes software developed by Adam Ciarcinski for the NetBSD project.
This product includes software developed by Adam Glass and Charles M. Hannum.
This product includes software developed by Adam Glass.
This product includes software developed by Advanced Risc Machines Ltd.
This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet.
This product includes software developed by Alex Zepeda.
This product includes software developed by Alistair G. Crooks.
This product includes software developed by Alistair G. Crooks. for the NetBSD project.
This product includes software developed by Allen Briggs
This product includes software developed by Amancio Hasty and Roger Hardiman
This product includes software developed by Berkeley Software Design, Inc.
This product includes software developed by Berkeley Software Design, Inc.
This product includes software developed by Bill Paul.
This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe)
This product includes software developed by Boris Popov.
This product includes software developed by Brad Pepers
This product includes software developed by Bradley A. Grantham.
This product includes software developed by Brini.
This product includes software developed by Causality Limited.
This product includes software developed by Charles D. Cranor and Seth Widoff.
This product includes software developed by Charles D. Cranor and Washington University.
This product includes software developed by Charles D. Cranor, Washington University, and the University of California, Berkeley and its contributors.
This product includes software developed by Charles D. Cranor, Washington University, the University of California, Berkeley and its contributors.
This product includes software developed by Charles D. Cranor.
This product includes software developed by Charles Hannum.
This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors.
This product includes software developed by Charles M. Hannum.
This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske.
This product includes software developed by Christian E. Hopps.
This product includes software developed by Christian Limpach
This product includes software developed by Christopher G. Demetriou for the NetBSD Project.
This product includes software developed by Christopher G. Demetriou.
This product includes software developed by Christos Zoulas.
This product includes software developed by Chuck Silvers.
This product includes software developed by Colin Wood for the NetBSD Project.
This product includes software developed by Colin Wood.
This product includes software developed by Cybernet Corporation and Nan Yang Computer Services Limited
This product includes software developed by Daishi Kato
This product includes software developed by Dale Rahn.
This product includes software developed by Daniel Widenfalk and Michael L. Hitch.
This product includes software developed by Daniel Widenfalk for the NetBSD Project.
This product includes software developed by Darrin B. Jewell
This product includes software developed by David Miller.
This product includes software developed by Dean Huxley.
This product includes software developed by Eduardo Horvath.
This product includes software developed by Eric S. Hvozda.
This product includes software developed by Eric S. Raymond
This product includes software developed by Eric Young (eay@@mincom.oz.au)
This product includes software developed by Eric Young (eay@cryptsoft.com)
This product includes software developed by Eric Young (eay@mincom.oz.au)
This product includes software developed by Ezra Story and by Kari Mettinen.
This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti.
This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti.
This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske.
This product includes software developed by Ezra Story.
This product includes software developed by Frank van der Linden for the NetBSD Project.
This product includes software developed by Gardner Buchanan.
This product includes software developed by Gary Thomas.
This product includes software developed by Gordon Ross
This product includes software developed by Gordon W. Ross
This product includes software developed by HAYAKAWA Koichi.
This product includes software developed by Harvard University and its contributors.
This product includes software developed by Harvard University.
This product includes software developed by Herb Peyerl.
This product includes software developed by Hubert Feyrer for the NetBSD Project.
This product includes software developed by Iain Hibbert
This product includes software developed by Ian F. Darwin and others.
This product includes software developed by Ian W. Dall.
This product includes software developed by Ichiro FUKUHARA.
This product includes software developed by Ignatios Souvatzis for the NetBSD Project.
This product includes software developed by Internet Initiative Japan Inc.
This product includes software developed by James R. Maynard III.
This product includes software developed by Jared D. McNeill.
This product includes software developed by Jason L. Wright
This product includes software developed by Jason R. Thorpe for And Communications, http://www.and.com/
This product includes software developed by Joachim Koenig-Baltes.
This product includes software developed by Jochen Pohl for The NetBSD Project.
This product includes software developed by Joerg Wunsch
This product includes software developed by John Birrell.
This product includes software developed by John P. Wittkoski.
This product includes software developed by John Polstra.
This product includes software developed by Jonathan R. Stone for the NetBSD Project.
This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project.
This product includes software developed by Jonathan Stone.
This product includes software developed by Juan Romero Pardines for the NetBSD Foundation, Inc. and its contributors.
This product includes software developed by Jukka Marin.
This product includes software developed by Julian Highfield.
This product includes software developed by Kazuhisa Shimizu.
This product includes software developed by Kazuki Sakamoto.
This product includes software developed by Kenneth Stailey.
This product includes software developed by Kiyoshi Ikehara.
This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berkeley and its contributors.
This product includes software developed by LAN Media Corporation and its contributors.
This product includes software developed by Leo Weppelman for the NetBSD Project.
This product includes software developed by Leo Weppelman.
This product includes software developed by Lloyd Parkes.
This product includes software developed by Luke Mewburn.
This product includes software developed by Lutz Vieweg.
This product includes software developed by MINOURA Makoto, Takuya Harakawa.
This product includes software developed by Manuel Bouyer.
This product includes software developed by Marc Horowitz.
This product includes software developed by Marcus Comstedt.
This product includes software developed by Mark Brinicombe for the NetBSD project.
This product includes software developed by Mark Brinicombe.
This product includes software developed by Mark Murray
This product includes software developed by Mark Tinguely and Jim Lowe
This product includes software developed by Markus Wild.
This product includes software developed by Martin Husemann and Wolfgang Solfrank.
This product includes software developed by Masanobu Saitoh.
This product includes software developed by Masaru Oki.
This product includes software developed by Mats O Jansson and Charles D. Cranor.
This product includes software developed by Mats O Jansson.
This product includes software developed by Matt DeBergalis
This product includes software developed by Matthew Fredette.
This product includes software developed by Matthias Pfaller.
This product includes software developed by Michael Graff for the NetBSD Project.
This product includes software developed by Michael Graff.
This product includes software developed by Michael L. Hitch.
This product includes software developed by Michael Shalayeff.
This product includes software developed by Michael Smith.
This product includes software developed by Mike Glover and contributors.
This product includes software developed by Mike Pritchard.
This product includes software developed by Minoura Makoto.
This product includes software developed by Nan Yang Computer Services Limited.
This product includes software developed by Niels Provos.
This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas.
This product includes software developed by Niklas Hallqvist.
This product includes software developed by Onno van der Linden.
This product includes software developed by Paul Kranenburg.
This product includes software developed by Paul Mackerras.
This product includes software developed by Per Fogelstrom
This product includes software developed by Peter Galbavy.
This product includes software developed by Phase One, Inc.
This product includes software developed by Philip A. Nelson.
This product includes software developed by Philip L. Budne.
This product includes software developed by RiscBSD.
This product includes software developed by Roar Thronæs.
This product includes software developed by Rodney W. Grimes.
This product includes software developed by Roger Hardiman
This product includes software developed by Roland C. Dowdeswell.
This product includes software developed by Rolf Grossmann.
This product includes software developed by Ross Harvey for the NetBSD Project.
This product includes software developed by Ross Harvey.
This product includes software developed by Scott Bartram.
This product includes software developed by Scott Stevens.
This product includes software developed by Shingo WATANABE.
This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors.
This product includes software developed by Soren S. Jorvang.
This product includes software developed by Stephan Thesing.
This product includes software developed by Steve Woodford.
This product includes software developed by Takashi Hamada
This product includes software developed by Takumi Nakamura.
This product includes software developed by Tatoku Ogaito for the NetBSD Project.
This product includes software developed by Terrence R. Lambert.
This product includes software developed by Tetsuya Isaki.
This product includes software developed by Thomas Gerner
This product includes software developed by Thomas Klausner for the NetBSD Project.
This product includes software developed by Tobias Weingartner.
This product includes software developed by Todd C. Miller.
This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project.
This product includes software developed by Tohru Nishimura for the NetBSD Project.
This product includes software developed by Tohru Nishimura. for the NetBSD Project.
This product includes software developed by TooLs GmbH.
This product includes software developed by Toru Nishimura.
This product includes software developed by Trimble Navigation, Ltd.
This product includes software developed by WIDE Project and its contributors.
This product includes software developed by Waldi Ravens.
This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/
This product includes software developed by Winning Strategies, Inc.
This product includes software developed by Wolfgang Solfrank.
This product includes software developed by Yasushi Yamasaki
This product includes software developed by Zembu Labs, Inc.
This product includes software developed by the Alice Group.
This product includes software developed by the Center for Software Science at the University of Utah.
This product includes software developed by the Charles D. Cranor, Washington University, University of California, Berkeley and its contributors.
This product includes software developed by the Computer Systems Engineering Group at Lawrence Berkeley Laboratory.
This product includes software developed by the David Muir Sharnoff.
This product includes software developed by the Harvard University and its contributors.
This product includes software developed by the Kungliga Tekniska Högskolan and its contributors.
This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory.
This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/)
This product includes software developed by the PocketBSD project and its contributors.
This product includes software developed by the RiscBSD kernel team
This product includes software developed by the RiscBSD team.
This product includes software developed by the SMCC Technology Development Group at Sun Microsystems, Inc.
This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia University.
This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors.
This product includes software developed by the University of California, Lawrence Berkeley Laboratory.
This product includes software developed by the University of Illinois at Urbana and their contributors.
This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman.
This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors.
This product includes software developed for the FreeBSD project
This product includes software developed for the NetBSD Project by Bernd Ernesti.
This product includes software developed for the NetBSD Project by Christopher G. Demetriou.
This product includes software developed for the NetBSD Project by Christos Zoulas
This product includes software developed for the NetBSD Project by Emmanuel Dreyfus.
This product includes software developed for the NetBSD Project by Frank van der Linden
This product includes software developed for the NetBSD Project by Ignatios Souvatzis.
This product includes software developed for the NetBSD Project by Jason R. Thorpe.
This product includes software developed for the NetBSD Project by John M. Vinopal.
This product includes software developed for the NetBSD Project by Matthias Drochner.
This product includes software developed for the NetBSD Project by Michael L. Hitch.
This product includes software developed for the NetBSD Project by Perry E. Metzger.
This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden
This product includes software developed for the NetBSD Project by Allegro Networks, Inc., and Wasabi Systems, Inc.
This product includes software developed for the NetBSD Project by Genetec Corporation.
This product includes software developed for the NetBSD Project by Jonathan Stone.
This product includes software developed for the NetBSD Project by Piermont Information Systems Inc.
This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network.
This product includes software developed for the NetBSD Project by Shigeyuki Fukushima.
This product includes software developed for the NetBSD Project by Wasabi Systems, Inc.
This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA.
This product includes software developed under OpenBSD by Per Fogelstrom.
This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse.
This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU).
This software includes software developed by the Computer Systems Laboratory at the University of Utah.
This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/).
This product includes software developed by Marshall M. Midden.
This product includes software developed or owned by Caldera International, Inc.
The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation.

In the following statement, the phrase ``this text'' refers to portions of the system documentation.

Portions of this text are reprinted and reproduced in electronic form in NetBSD, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document.

The original Standard can be obtained online at http://www.opengroup.org/unix/online.html.

This notice shall appear on any product containing this material

This product includes software developed by the Alice Group.
This product includes software developed by David Miller.

The End